Embroidery Hooping: Tutorial, Tips & Aids

Embroidery Hooping: Tutorial, Tips & Aids

A Complete Guide to Machine Embroidery Hooping

“The quality of any embroidery project starts with how well your material and stabilizer are hooped”

This complete guide to embroidery hooping will cover:

  • The difference between commercial & home embroidery hoops.
  • Give you a basic tutorial on how to properly hoop fabric without, well… Jumping through hoops.
  • Show you some useful techniques & tricks that’ll help you hoop easier.
  • The difference between hooping and floating.
  • Explain hooping aids and why / when you might need them.

Commercial vs. Home Embroidery Hoops

Commercial vs Home Machine Embroidery Hoops

Having come from the commercial side of embroidery, I must admit that one of the things that shocked me most when entering the home or hobbyist embroidery industry was the shape of the hoops…

You see, in the commercial embroidery industry, the shapes of most hoops are circular & round. While in the home embroidery industry, most hoops are square or rectangular which is why you get sizes like 5” x 7” hoops.

Now logically, the commercial (or circular) hoops do make more sense. The reason is because with the rectangular hobbyist hoops, there are 4 corners where the fabric is held securely. However, the long straight areas of the hoop between the corners are not held as tight or securely. This leads to the fabric becoming loose and causing issues like design mis-registration & puckering.

Now with the commercial hoops being circular, the material is held down securely and evenly within all areas of the hoop. Instead of only having 4 strong corners, pressure is evenly dispersed throughout the entire hoop which makes the fabric less likely to become lose & pull inwards. Think of it like a drum: a drum is circular so that the drum “skin” (as they call it) can be stretched evenly across the drum to make it tight.

To this day, I personally do prefer to use circular hoops over square- or rectangular-shaped ones because it does a better job of holding your fabric & stabilizer securely in place. However, it is in no way a must. Some home and commercial crossover machines do come with circular hoops, such as the Redline 1501 embroidery machine. But you’re often able to custom order circular hoops for most home machine brands, too.

Once again, you in no way need to have circular hoops. I’ll show you some helpful tips & tricks on how to secure the long straight areas of rectangular hoops in the Hooping Tips, Tricks & Techniques section below… But first, let’s cover some hooping basics with a quick tutorial.

 

Machine Embroidery Hooping Tutorial

I often see embroiderers take a screwdriver & tighten their hoops as much as they possibly can after hooping… Do not do this on materials you care about! It will cause “hoop burn,” making the fabric look stretched and worn. Instead, try following these hooping instructions.

Step 1: Get Your Hoop & Fabric Ready

The first step towards proper hooping is to grab the piece of material that you’ll be stitching on, fold it in half, and give it a tiny bit of pressure. This will give you a measurement of how thick the fabric is when folded and gives you a visual guideline showing you how to properly pre-adjust the space between each half of your hoop. The idea is that when you pre-adjust the hoop to the right size beforehand, you won’t play around tightening it after the material is already hooped, which causes hoop burn on the material.

Folded Fabric for Hooping
You will then take your hoop and pull on the corner that has the adjustable knob and loosen or tighten it to make the separation between each piece of the hoop roughly the same size as the visually measured folded fabric.

Size Hoop

Step 2: Hoop Your Material

Next, you will place the bottom half of your hoop on the table in front of you so that adjustable corner with the knob is the furthest away from you. After properly laying your material and stabilizer on top of the bottom half of the hoop that is on the table, you will take the top half of the hoop and in one swift motion, push it forward and down into the bottom half of the hoop to ‘pop’ it into place. If pre-adjusted properly, there should be a little bit of resistance, but you shouldn’t be fighting with the top piece of the hoop to press it in.

Pushing Hoop in

Remember to not tighten the hoop by adjusting the knob after the fabric has already been hooped. I see this all the time with embroidery beginners; they first hoop very loosely, then aggressively turn the knob to tighten the hoop. Many even take screw drivers & tighten the hoop to the max. This is a huge waste of time, causes fabric burn, and is harmful towards your embroidery stitch out.

Instead of tightening the hoop by turning the knob afterwards, while the hoop is still on the table grab the material sticking out of the longer sides of the hoop and pull it gently. Then pick up the hoop and push the corners of the hoop in slightly, making it drum-tight and machine-ready.

That’s it, now you’re ready to place your hoop on your machine and start stitching!
Tightening Embroidery Hoop

Embroidery Hooping for Beginner’s Video Tutorial:

If you’re more of a visual learner, here’s a great quick tip video I put together explaining the process.

 

Hooping Tips, Tricks & Techniques

Now that you know how to hoop and the difference between commercial & home embroidery hoops, here are some helpful techniques and tricks that’ll help you tackle any embroidery hooping project:

1. Use the Correct Hoop Size

Simply put, you will always get the best results if you use a hoop that is closest in size to the embroidery design you are running. For example, if your design is 3.5” x 3.8”, use a 4” x 4” hoop, not a 5” x 7”. This is a basic principle but surprisingly, quite a few embroiderers don’t follow it.

2. Use T-pins for Large Rectangular Hoops

If you ever need to secure your fabric in a large rectangular hoop, I suggest you use T-pins to hold the fabric securely in place. Please note that this technique should only be used on stabilizers or fabrics that are not overly important to you as the T-pins may leave holes and mark them.

For this technique, you’ll hoop your fabric as you normally would (see the tutorial section above for more details). Once this is complete, you’ll use T-pins to secure the stabilizer or fabric in place & stop any potential movement. The T-pins should be inserted where the stabilizer or fabric sticks out between the two hoop frames after being hooped. They should be inserted flush with the frame. This way, when the stabilizer or fabric begins to pull in around the loose areas of the frame, the T-pins will be there to catch against the frame and stop any movement.

We recommend inserting these T-pins around the long straight areas of hobbyist hoops as these sections are not held as tightly or securely. The corners will not require T-pins.

Here’s a quick video to show you the technique in action:

3. Use Double Sided Tape

Using double sided tape is a great technique when dealing with sheer, slippery, or stretchy fabrics. The reason being that the stabilizer which touches the outside part of the hoop does its job as stated, its “stability” holds to the plastic part of the outer hoop. The issue of “puckering” within a design often occurs when the material touching the plastic of the inner hoop doesn’t “grip” the material. So, when you have one part holding securely and the other slipping, the result is distortion and puckering within the design.

Applying double sided tape to the outside of the inner hoop where the material touches the hoop eliminates the slipping between the stabilizer and fabric and will give you much better results.

The best part is, the tape will work for multiple hoopings, until it loses its “stickiness”, then you simply remove and reapply a new piece. I’ve also found that it doesn’t harm or leave any residue to most fabric types. Essentially it does almost the same job as the “t-pin” technique but is less invasive to the fabric.

This technique is a win-win in my books.

Here’s a quick video to show you the technique in action:

 

Hooping or Floating Your Embroidery: What’s the Difference?

I’ve seen a big movement in recent years where people are “floating” their embroidery. This essentially means that the user hoops a piece of stabilizer and then “floats” the material/item being embroidered onto the stabilizer.

I’m not a big fan as this is not a “one-size-fits-all” way of hooping. My rule of thumb is if you can’t hoop an item, or if it is specifically digitized as an in-the-hoop project that requires you to float pieces of fabric, then you should float it. But as far as I’m concerned, it should be a last resort. You will always get better end results if you securely hoop your stabilizer and fabric.

If you do need to float an item or material as opposed to hooping it, I strongly suggest extra measures are taken to ensure better results. These can include basting stitches, embroidery spray adhesive, tacky stabilizers, pins, taping… pretty much anything to help secure the design to the stabilizer.

One of the biggest registration problems I see–things not lining up–on well-digitized designs is because the item was “floated” and not hooped securely.

 

Embroidery Hooping Aids, Stations & Boards Make it Easy

Embroidery Hooping Station

If you’ve ever tried hooping with an embroidery hooping aid, I don’t have to explain the perks to you… If you haven’t, well, you’re in for a treat! Embroidery hooping stations, boards & systems are great aids that help you in hooping quicker & easier.

Now, I would personally recommend a hooping aid for anyone who:

  • Has trouble hooping.
  • Hoops difficult items (like baby onesies, sleeves, embroidery buddies, socks, etc).
  • Owns an embroidery business.
  • Makes multiple similar items at once (for example 10 shirts).
  • Doesn’t enjoy hooping.

I say this because hooping aids really do speed up the entire process and reduce the chances that you’ll make a mistake and have to hoop again.

Not to mention they actually make hooping fun!

My personal recommendation for quality hooping station that won’t break the bank is the Echidna Hooping Station. It’s the only hooping aid on the market that uses magnets to allow you to hoop quicker & easier than ever.

Simply place your hoop on the elevated non-slip board, secure it in place with powerful magnets and hoop… It’s that easy!

These hooping aids fit virtually every sized hoop on the market and are not specific to different machine brands. It’s incredibly easy to use & unlike other hooping stations, they don’t require additional add-on attachments, have a giant instruction manual and don’t cost a fortune.

If you’d like to learn more about these amazing hooping stations, click here. Or simply watch the video below:

What’s Next?

Hopefully this article has taught you a thing or two about hooping.

If you’re new to machine embroidery, I would suggest that you try hooping a few items following the steps provided in the tutorial section above. Although hooping isn’t the most fun part of embroidery, it is one of the most important, and as the old saying goes, “practice makes perfect”.

Now if you’re more experienced and landed on this article in hopes of finding an easier way to hoop, I highly suggest you do check out the Echidna Hooping Station. It makes the entire hooping process much faster, easier and less frustrating.

If you did enjoy the videos provided here as well, please don’t forget to subscribe to YouTube channel! I appreciate your support & happy hooping!

By | 2019-09-04T12:17:23+00:00 August 30th, 2019|Embroidery Basics, Machine Embroidery How to Techniques|1 Comment

About the Author:

One Comment

  1. punch embroidery design August 30, 2019 at 11:30 am - Reply

    This is really informative article for all the related department. I am really impressed from your writing skill.

Leave A Comment Cancel reply

*